DVD600II
Operating the DVD600II DVD Changer
Loading DiscsNotes on DVD-Audio discs: Y Do not attempt to change or touch the disc
To load discs in the DVD600II, first make certaintray carousel while it is moving.
Y The DVD600II is not capable of playing selec-
that the unit is turned on by pressing the Main
tions in the DVD-Audio format. However, manyY Do not attempt to rotate the disc tray by
Power Switchso that it latches, and
DVD-Audio discs include audio tracks in thehand. If the tray drawer or carousel tray
then the System Power Controlor the
PCM, Dolby Digital or other formats which theappears to be stuck, contact your local JBL
Open/Close Buttonf or Play/Pauseauthorized service center.
DVD600II is capable of playing. You may need
Button. The Status Indicator
to press the Title Button x rather than the
turns green.Y Do not load more than one disc in each slot in
Menu Button z in order to access these
the tray and do not attempt to place a stan-
formats.
Next, if needed, press the Open/Close Buttondard 5-inch (12cm) disc over a smaller 3-inch
f until the Disc Trayopens.Y Some DVD-Audio discs display a still picture(8cm) disc.
while a selection is playing. Sometimes, this
Once the discs are loaded, press the Open/
Holding the discs by the edge, gently place each
picture may disappear when play is stopped andClose Buttonf to close the disc tray.
one into one of the compartment slots in the
the DVD600II is placed in the Resume mode. ToWhen the tray drawer closes, the disc that was
drawer. Note that there is a number embossed
restore the picture, fully stop play by pressinglast in the center position facing outward in the
onto the drawer tray at the right of the disc slot.
the Stop Button twice before contin-tray will be readied for playback. After the
This is the number for that specific disc position;
uing play.drawer closes, you will see an indication of
it will be used to indicate the disc in both theReading in the Information Display to alert
Information Display and the on-screen displays. you to the fact that the unit is determining the
type of disc (DVD, MP3 or CD) and is reading
When loading discs, please note the following:the data for track, chapter, title and other infor-
mation about the disc. At the same time, the
Y The DVD600II will play discs with the followingDisc Number Indicatorfor the disc in use
logos only. DO NOT attempt to play anotherwill begin to flash, indicating which disc is
type of disc, as shown in the list on page 46.
ready to be played.
You will also see the On Screen Library dis-
played (see Figure 17). It will take about one
Figure 17. On Screen Library Displayminute for all discs to be identified. You may
Y The DVD600II will only play discs in the NTSCinterrupt the process by pressing Stop, by press-
video format. It will not play discs for otherTo move the discs in the tray so that you maying Enter to select a disc, or by scrolling down
standards such as PAL or SECAM.insert discs in slots that are partially hiddento the Exit button. When the process is com-
inside the disc tray drawer, press the Disc Skipplete, press Play to play the current disc, or
Y Playback capability for CD-RW discs will vary
Button. Each press of the button willscroll to select any disc.
according to the quality of the CD-RW disc.
move the carousel tray one position to the left
On some occasions, it is possible that CD-RW
If the tray was closed by pressing one of the
(counterclockwise). There may be a slight delay
discs may not play on the DVD600II. This does
five Direct Access Buttons on the
of several seconds before the carousel moves to
not indicate any problem with the DVD600II.
front panel, the On Screen Library will not be
the next disc, which is normal. You may avoid
activated.
Y The DVD600II will only play discs that arethe delay by pressing the Disc Skip Button
coded for Region 1 or discs that are open totwice.You may access the On Screen Library later by
being played in all regions. Discs that contain
stopping play of the current disc and pressing
a Region Code of 2, 3, 4, 5 or 6 (as noted by aY To access all disc positions, the unit must be
the On Screen Library Button . Use the
number inside a world map logo on the discOsin the full-stop position. If the unit is in the
D/¤Buttonsy31to scroll to the desired
cover jacket or case) will not play.Play mode, press the Stop Button
disc, and the Set Button 28 to begin play of
twice.
Y Both 5-inch (12cm) and 3-inch (8cm) discs maythat disc.
be used.Y If the disc tray drawer is opened while a disc
Once the discOs data has been read, the type of
is playing, the Play Exchange feature allows
disc (DVD or CD) will be displayed by the Disc
Y When loading CD audio discs, load the discsyou to change the remaining four discs.
Type Indicatorand the disc will begin
with the label side up.Simply press the Disc Skip Button
playing. The discOs track timing information
to move the discs in the tray in one direction
Y When loading DVD discs with printed labels,or the other.and other relevant data will appear in the
Information Display. For CD discs only,
load them label side up.
a Status Menu Bar will appear in the on-screen
IMPORTANT NOTES
Y Some DVD discs are double-sided. The titledisplay. To view this display for DVD discs,
ON DISC LOADING
information for these will be printed on thepress the Status Button e.
Y Remove all discs from the tray before
inner ring of the disc, very close to the center
moving the player.
hole. The title for the side you wish to playThe Disc Number Indicatorwill show a
should be facing up.lighted number for the disc slot positions that
Y Make certain that all discs are properly seated
are occupied, and the disc in use will flash.
before closing tray drawer.
Y The DVD600II is also capable of playing discs
containing MP3 audio files.Playback Basics
Y Do not push the disc tray drawer with the
Basic playback with the DVD600II involves func-
power off.
tions similar to those you may be familiar with
14for conventional CD players or changers: |
ACEC
